Description: Specify whether TPO calls are recorded or not. This is valid only when active recording is enabled. The turret recorder module will not be aware of these calls existence.
Related settings: Tag and re-invite direct calls (application.global.enablecalltag)
Description: Specify whether the group intercom is recorded through active recording or if the infrastructure manage to record intercom on its own. Setting this parameter to true will allow the turret to send recording session for group intercom.
Note: If the key application.recorder.startrecordingatlogin is set to true, the group intercom is always recorded whatever the value of this parameter.
Related settings: Record intercom calls as they were on LD (SIPRec only) (profile.setting.recording.forceintercomonld) Start recording at login (application.recorder.startrecordingatlogin)
Location: Terminal Boot Settings
Timezone
Timezone standard bias
Key: profile.setting.timezone.standardbias
Description: Bias value to be used during local time translations that occur during standard time. This value is added to the value of the Bias setting to form the bias used during standard time. In most time zones, the value of this member is zero.
See TCN-Timezone management or MSDN documentation on TIME_ZONE_INFORMATION.
Constraint: Numerical value, in minutes
Related settings: Timezone daylight hour (profile.setting.timezone.daylighthour) Timezone daylight bias (profile.setting.timezone.daylightbias) Timezone bias (profile.setting.timezone.bias) Timezone standard month (profile.setting.timezone.standardmonth) Timezone standard day of week (profile.setting.timezone.standarddayofweek) Timezone standard day (profile.setting.timezone.standardday) Timezone standard hour (profile.setting.timezone.standardhour) Timezone daylight month (profile.setting.timezone.daylightmonth) Timezone daylight day of week (profile.setting.timezone.daylightdayofweek) Timezone daylight day (profile.setting.timezone.daylightday)
Mixed mode
When Mixed recording mode is used, the recording channels must be configured. The setting below is one example of the available channels:
Description: Logical audio devices recorded on channel 0 (mixing mode only).
A list of semi-colon (;) separated values.
Possible values are: - Handsets: HS1 HS2 - The headset: The device to record depends on the value used for the "Headset device association" setting (profile.setting.hdswapdevice) - Applets (includes LD/LDI and HF/HFI devices): applet.1 applet.2 applet.3 applet.4 applet.7 applet.8 - Applets (monitor lines only, selected state can be distinguished): applet.1.LD applet.2.LD applet.3.LD applet.4.LD applet.7.LD applet.8.LD applet.1.LD.selected applet.2.LD.selected applet.3.LD.selected applet.4.LD.selected applet.7.LD.selected applet.8.LD.selected - Applets (hand free lines only): applet.1.HF applet.2.HF applet.3.HF applet.4.HF applet.7.HF applet.8.HF - Monitor lines: LD (means all LD devices) LD.selected (means all LD lines when selected) LD1.x (*) LD2.x (*) LD1.x.selected (*) LD2.x.selected (*) - Hand free lines: HF (means all HF devices) HF1.x (*) HF2.x (*) - Monitor intercoms: LDI1.x (*) LDI2.x (*) LDI1.x.selected (*) LDI2.x.selected (*) - Hand free intercoms: HFI1.x (*) HFI2.x (*)
(*) x is one of {1, 2, 3, 4, 5, 6, 7, 8, 9, a, b, c, d, e, f, g, h, i, j, k, l, m, n, o, p, q, r, s, t, u, v, w, x, y, z, ~}
Note: priorities for conflicting devices are defined based on the order in which channels are listed (numercial order). This means that: (a) profile.setting.recording.channel.0.devices = LD profile.setting.recording.channel.1.devices = LD1.1 * In (a), LD1.1 will use channel id 1 and all the other LDs (LD1.2, LD1.3...) will use 0. (b) profile.setting.recording.channel.0.devices = LD1.1 profile.setting.recording.channel.1.devices = LD * In (b), all the LDs (LD1.1, LD1.2, LD1.3...) will use channel id 1. Note: for LD devices, when the "selected" channel id is not specified, the "idle" value is used. Note: the *.selected values can only be used when different loudspeakers are assigned to the idle and select states of the monitoring applet.
