Configuration keys

Location: Terminal Boot Settings, TPO Shared Settings, TPO Boot Settings, boot

SNMP

SNMP enabled	truefalse
Key: application.global.snmp.enable Description: When SNMP agent is enabled : - Turret firmware / TPO service listen to SNMP management application requests on primary IP Address of the configured adapter. It listens on SNMP port 161. Depending on the SNMP request version, firmware / service answers requests in SNMP V1 or V2C. - Turret firmware / TPO service sends SNMP V2C traps to the configured trap targets on event occurrence When SNMP agent is not enabled : - Turret firmware / TPO service does not listen to SNMP request. - Turret firmware / TPO service does not send SNMP traps. Constraint: true\|false Related settings: SIP server adapter (application.boot.sip.adapter) SNMP trap targets (application.global.snmp.trap.targets)

Location: Terminal Boot Settings, TPO Boot Settings, SNMP, boot

SNMP

SNMP trap targets
Key: application.global.snmp.trap.targets Description: When it is enabled SNMP agent sends trap on particular event occurrence. By default, no trap target is defined. Multiple targets may be defined (see constraint description), in that case the same trap is sent on each defined target. Constraint: Should contains IP address or IP addresses list (comma separated). Exemples: 123.45.67.89 123.45.67.89,234.56.78.90 Related settings: SNMP enabled (application.global.snmp.enable) SNMP trap check delay (application.global.snmp.trap.checkdelay)

Location: Terminal Boot Settings, TPO Boot Settings

SNMP

SNMP ARP check timer
Key: application.global.snmp.arpcheck.timer Description: Periodically, SNMP module checks the association between the virtual IP address and MAC address. If it changes, the module sends a SNMP trap. The default period is 30000 ms. Constraint: This value cannot be less then minimum trap check delay, see other related keys.

Location: Terminal Boot Settings

SNMP

Motherboard AUX temperature SNMP traps enable	truefalse
Key: application.global.snmp.trap.CA.MBtemp.AUX.enable Description: On CA turret models, motherboard AUX temperature has an inconsistent value exceeding temperature threshold. Nevertheless, this value is 'normal'. SNMP traps are sent several times by minutes and are traced in syslog file. If this setting is disabled (value = false), system avoid sending SNMP traps and avoid fulfilling syslog file with traces about motherboard AUX temperature. Constraint: true\|false

Location: Terminal Boot Settings, TPO Boot Settings, boot, boot

SNMP

SNMP read community
Key: application.global.snmp.read.community Description: "Security" in SNMP V2C consist in a verification of the community contained by request message. If the community request message contains is allowed to access variable, SNMP module send a response with the requested information. Otherwise SNMP module send a response containing the SNMP NO ACCESS error code. Access control is made case un-sensitive. Constraint: String containing allowed community name or list of semicolon (';') separated community names. IPTreadcommunity iptrademgm;iptrade

Location: Terminal Boot Settings, TPO Shared Settings, TPO Boot Settings

SNMP

SNMP trap check delay
Key: application.global.snmp.trap.checkdelay Description: Turret Firmware / TPO service periodically checks trap value in oder to send traps when traps conditions are encountered. This setting defines default trap check periodicity in millisecond. Default value is 300000 milliseconds (5 minutes). Constraint: This value cannot be less then minimum trap check delay, see other related keys. Related settings: SNMP trap targets (application.global.snmp.trap.targets) SNMP minimum trap check delay (application.global.snmp.trap.mincheckdelay) SNMP particular trap check delay (application.global.snmp.trap.trapID.checkdelay)

Location: Terminal Boot Settings, TPO Shared Settings, TPO Boot Settings

SNMP

SNMP minimum trap check delay
Key: application.global.snmp.trap.mincheckdelay Description: This setting ensure all configured trap check delay is at least equal to a certain value. Default value is 5000 milliseconds (5 seconds). Constraint: Cannot be less then 1000 milliseconds. Related settings: SNMP trap check delay (application.global.snmp.trap.checkdelay)

Location: Terminal Boot Settings, TPO Boot Settings, SNMP

SNMP

SNMP object value validity
Key: application.global.snmp.object.updatedelay Description: Some values qualified as "continuous" changes all the time. Successive requests of the same "continuous" object could cause turret firmware / TPO service / TSS Virtual Appliance to update SNMP data uselessly. On object request, if object update has been done previously and value is not older then validity period, object value is not reevaluated. This setting defines default object value validity period. By default it is set to 10000 milliseconds (10 seconds) Constraint: Cannot be less then 1000 milliseconds. Related settings: SNMP particular object value validity (application.global.snmp.objectID.updatedelay)

Location: Terminal Boot Settings, TPO Boot Settings, SNMP

SNMP

SNMP - Trap limit - Low memory (KB)
Key: application.global.snmp.trap.minfreememory Description: Following trap is sent when turret free memory is less or equal to the setting value. turret.sysinfo.sysInfoTraps.lowMemory (1.3.6.1.4.1.30191.1.1.512.2) Object related to that trap is: turret.sysinfo.freeMemory (1.3.6.1.4.1.30191.1.1.3) Value of this object is expressed in kilobytes (KB) Following trap is sent when TPO free memory is less or equal to the setting value. tpo.sysinfo.sysInfoTraps.lowMemory (1.3.6.1.4.1.30191.2.1.512.2) Object related to that trap is: tpo.sysinfo.freeMemory (1.3.6.1.4.1.30191.2.1.3) Value of this object is expressed in kilobytes (KB) Following trap is sent when TSS VA free memory is less or equal to the setting value. tssva.sysinfo.sysInfoTraps.lowMemory(1.3.6.1.4.1.30191.3.1.512.2) Objects related to that trap are: tssva.sysinfo.freeMemory (1.3.6.1.4.1.30191.3.1.3) tssva.sysinfo.totalmemory(1.3.6.1.4.1.30191.3.1.1) Value of this object is expressed in kilobytes (KB)

Location: Terminal Boot Settings

SNMP

SNMP - Trap limit - High temperature (°C)
Key: application.global.snmp.trap.maxonboardtemp Description: Following trap is sent when onboard temperature is greater or equal to the setting value. turret.sysinfo.sysInfoTraps.highTemparature (1.3.6.1.4.1.30191.1.1.512.3) Objects related to that trap are: turret.sysinfo.cpuTempTable.cpuTempEntry.cpuTemp(1.3.6.1.4.1.30191.1.1.25.1.2) turret.sysinfo.motherboardTempTable.motherboardTempEntry.motherboardTemp(1.3.6.1.4.1.30191.1.1.26.1.2) Value of those objects is expressed in degrees Celsius (°C)

Location: Terminal Boot Settings

SNMP

SNMP - Trap limit - DB low space (KB)
Key: application.global.snmp.trap.db.minfreememory Description: Following trap is sent when free space of one of the embedded data bases is less or equal to the setting value. turret.embededDB.embededDBTraps.eosLowMemory (1.3.6.1.4.1.30191.1.7.512.1) Object related to that trap is: turret.embededDB.eosTable.eosEntry.eosFreeMemory (1.3.6.1.4.1.30191.1.7.2.1.5) Value of this object is expessed in kilobytes (KB)

SNMP over WebSocket

To enable SNMP over WebSocket, the WebSocket URI of the Assure server must be configured with the following setting.

Secured SNMP is achieved by using the WebSocket Secure (WSS) protocol.

The WebSocket (WS) protocol is used when the URI starts with "ws://".

The WebSocket Secure (WSS) protocol is used when the URI starts with "wss://".

Location: Terminal Boot Settings, TPO Boot Settings, SNMP

SNMP

SNMP WebSocket targets
Key: application.global.snmp.websocket.targets Description: Defines WebSocket targets for SNMP monitoring. Multiple targets can be defined. Constraint: URIs separated with a pipe character ("\|"). Example : ws://echo.websocket.org\|wss://echo2.websocket.org If connecting to Tradesense then the format should be: wss:///snmp Related settings: SNMP Default Translate Mode (application.global.snmp.translate.mode) Enable SNMP over UDP (application.global.snmp.enableUDP)